4 lines
5.0 KiB
JSON
4 lines
5.0 KiB
JSON
{
|
||
"result": "[Ste97] A generalized temperature-dependent, non-Newtonian Hele-Shaw flow in injection and compression moulding (1997)\nMathematical Methods in The Applied Sciences, pp. 1199-1222\nDate: 1997-09-25\nBy J. Steinbach - 5 citations - 0.2 cit./yr\nDOI: 10.1002/(SICI)1099-1476(19970925)20:14<1199::AID-MMA910>3.0.CO;2-5\nPDF X\n\nA generalized Hele-Shaw flow is derived and analysed in injection and compression moulding which contains non-isothermal and non-Newtonian rheological behaviour of the molten polymers as well as non-symmetric effects. The corresponding fixed domain formulations for the flow are investigated from a mathematical point of view. Different approaches for the determination of the temperature and some viscosity models are discussed. Together with an outline of the proposed solution algorithm special finite element techniques are described for the numerical treatment of this complex non-linear moving boundary problem.\n\n[Soh86] Boundary conditions in the modeling of injection mold-filling of thin cavities (1986)\nPolymer Engineering and Science, pp. 893-899\nDate: 1986-07-01\nBy S. K. Soh, Chin-Jui Chang - 2 citations - 0.0 cit./yr\nDOI: 10.1002/PEN.760261209\nPDF X\n\nA governing equation for injection mold-filling of thin cavities with a power-law fluid is derived. The interaction between upstream delivery channel flow and cavity flow results in a continuously changing gate condition as the total viscous dissipation of the delivery channel-cavity assembly is minimized. Depending upon the relative magnitude of pressure drops or viscous dissipation across the channel and the cavity, the boundary conditions which determine the cavity filling process will lie between the following two limiting cases: a Cauchy type gate condition such that the location of the melt front is completely determined by the upstream flow; a Cauchy type melt front condition in which the gate condition is controlled by the downstream flow. For most injection molding cases this may be manifested as equilibration of dissipation density on the melt front. Experimentally observed melt front locations from isothermal, Newtonian filling of a constant gap rectangular cavity and of a bi-gap rectangular cavity are reported and the validity of the limiting cases are tested.\n\n[Zha04] A low‐dimensional description of transient shear‐thinning free‐surface flow in thin cavities, as applied to injection molding (2004)\nInternational Journal for Numerical Methods in Fluids\nDate: 2004-01-10\nBy Sheng X. Zhang, R. Khayat - 2 citations - 0.1 cit./yr\nDOI: 10.1002/fld.630\nPDF X\n\nAbstract A spectral methodology is proposed to examine the influence of shear thinning on the transient free‐surface flow inside a three‐dimensional thin cavity. The problem is closely related to the filling stage during the injection molding process. The moving domain is mapped onto a rectangular domain at each time step of the computation. A modified pressure is introduced that is governed by the Laplace's equation. The flow field is expanded in Fourier series along the lateral direction in the mapped domain, and the Galerkin projection is used to derive the equations that govern the expansion coefficients, which are solved using a variable‐step finite‐difference scheme. This approach is valid for simple and complex cavities as illustrated for the cases of a flat plate with variable and constant thickness. It is shown that, even for highly non‐linear shear‐thinning flow, only a few modes are needed for convergence. Shear thinning generally influences the flow behaviour. However, shear thinning may enhance or prohibit the flow, depending whether the flow rate at the entrance of the cavity is fast or slow, respectively. Copyright © 2004 John Wiley & Sons, Ltd.\n\n[Hie83] Filling thin cavities of variable gap thickness: A numerical and experimental investigation (1983)\nPolymer Engineering and Science, pp. 20-26\nBy C. Hieber, L. Socha, S. Shen, K.-K. Wang, A. Isayev - 35 citations - 0.8 cit./yr\nDOI: 10.1002/PEN.760230106\nPDF X\n\nA theoretical and experimental investigation is presented for filling thin cavities of variable gap thickness. The modeling is based upon a finite-element/finite-difference formulation for an inelastic power-law fluid and includes the effects of viscous heating and conduction upon the flow dynamics. Extensive results are presented for polypropylene and polystyrene melts injected into two variable-gap-thickness cavities, of which one has an insert. Good agreement is found between the predictions and measurements concerning the shape of the advancing melt front, the location of weld lines, and the temporal pressure trace at various positions in the cavity.\n\nPDF symbols - ✓ PDF available; X No PDF available; … PDF download attempt in progress\n\nWhen using cite keys in your reply to the user, format as [[cite_key]](url), where url is https://doi.org/<DOI> for the DOI shown above (or the exact Link shown for papers without one), separating multiple with commas. In workspace files, keep bare [cite_key] markers with no URLs."
|
||
}
|